The TUSB2046x is a 3.3-V CMOS hub device that provides one upstream port and four downstream ports in compliance with the Universal Serial Bus (USB) specification as a full-speed hub. Because this device is implemented with a digital state machine instead of a microcontroller, no firmware
programming is required. Fully compliant USB transceivers are integrated into the ASIC for all upstream and downstream ports. The downstream ports support full-speed and low-speed devices by automatically setting the slew rate according to the speed of the device attached to the ports. The configuration of the BUSPWR pin selects either the bus-powered or the self-powered mode.

Configuring the GANGED input determines the power switching and overcurrent detection modes for the downstream ports. If GANGED is high, all PWRON outputs switch together and if any OVRCUR is activated, all ports transition to the power-off state. If GANGED is low, the PWRON outputs and OVRCUR inputs operate on a per-port basis.

The TUSB2046x provides the flexibility of using a 6-MHz or a 48-MHz clock. The logic level of the TSTMODE terminal controls the selection of the clock source. When TSTMODE is low, the output of the internal APLL circuitry is selected to drive the internal core of the device. When TSTMODE is high, the TSTPLL/48MCLK input is selected as the input clock source and the APLL circuitry is powered down and bypassed. The internal oscillator cell is also powered down while TSTMODE is high. Low EMI emission is achieved because the TUSB2046x can usee a 6-MHz crystal input. Connect the crystal as shown in Figure 6. An internal PLL then generates the 48-MHz clock used to sample data from the upstream port and to synchronize the 12 MHz used for the USB clock. If low-power suspend and resume are desired, a passive crystal or resonator must be used. However, a 6-MHz oscillator may be used by connecting the output to the XTAL1 pin and leaving the XTAL2 pin open. The oscillator TTL output must not exceed 3.6 V.

For 48-MHz operation, the clock cannot be generated with a crystal using the XTAL2 output because the internal oscillator cell supports only the fundamental frequency. Other useful features of the TUSB2046x include a package with a 0.8-mm pin pitch for easy PCB routing and assembly, push-pull outputs for the PWRON pins eliminate the need for pullup resistors required by traditional open-collector I/Os, and OVRCUR pins have noise filtering for increased immunity to voltage spikes.

• Fully Compliant With the USB Specification as a Full-Speed Hub: TID #30220231
• 32-Pin LQFP (1) Package With a 0.8-mm Terminal Pitch or QFN Package With a 0.5-mm Pin Pitch
• 3.3-V Low-Power ASIC Logic
• Integrated USB Transceivers
• State Machine Implementation Requires No Firmware Programming
• One Upstream Port and Four Downstream Ports
• All Downstream Ports Support Full-Speed and Low-Speed Operations
• Two Power Source Modes
  • Self-Powered Mode
  • Bus-Powered Mode
• Power Switching and Overcurrent Reporting Is Provided Ganged or Per Port
• Supports Suspend and Resume Operations
• Supports Programmable Vendor ID and Product ID With External Serial EEPROM
• 3-State EEPROM Interface Allows EEPROM Sharing
• Push-Pull Outputs for PWRON Eliminate the Need for External Pullup Resistors
• Noise Filtering on OVRCUR Provides Immunity to Voltage Spikes
• Package Pinout Allows 2-Layer PCB
• Low EMI Emission Achieved by a 6-MHz Crystal Input
• Migrated From Proven TUSB2040 Hub
• Lower Cost Than the TUSB2040 Hub
• Enhanced System ESD Performance
• No Special Driver Requirements; Works Seamlessly With Any Operating System With USB Stack Support
• Supports 6-MHz Operation Through a Crystal Input or a 48-MHz Input Clock

(1)JEDEC descriptor S-PQFP-G for low-profile quad flatpack (LQFP).

• Function
• USB2
• USB speed (Mbps)
• 12
• Supply voltage (V)
• 3.3
• Rating
• Catalog
• Operating temperature range (C)
• -40 to 85

TUSB2046I的完整型号有：TUSB2046IBVF、TUSB2046IBVFR，以下是这些产品的关键参数及官网采购报价：

TUSB2046IBVF，工作温度：-40 to 85，封装：LQFP (VF)-32，包装数量MPQ：250个，MSL 等级/回流焊峰值温度：Level-3-260C-168 HR，引脚镀层/焊球材料：NIPDAU，TI官网TUSB2046IBVF的批量USD价格：1.716（1000+）

TUSB2046IBVFR，工作温度：-40 to 85，封装：LQFP (VF)-32，包装数量MPQ：1000个，MSL 等级/回流焊峰值温度：Level-3-260C-168 HR，引脚镀层/焊球材料：NIPDAU，TI官网TUSB2046IBVFR的批量USD价格：1.329（1000+）

EVM430-FR6047 — MSP430FR6047 超声波感应评估模块

EVM430-FR6047 评估套件是一款开发平台，可用于评估适用于超声波检测应用（如智能水表）的 MSP430FR6047 MCU 的性能。MSP430FR6047 MCU 是一款超低功耗器件，具有集成的超声波检测模拟前端 (USS)，可实现高精度超声波测量。该器件还包括用于优化信号处理的低耗能加速器 (LEA)，可帮助优化功耗，延长电池寿命。该 EVM 提供了一种灵活的解决方案，从而让工程师能够使用 MSP430FR6047 MCU 和各种传感器（范围从 50KHz 到 2.5MHz）快速进行评估和开发。该 EVM 能够利用板载 LCD 显示屏和适用于射频通信模块的连接器显示测量参数。

EVM430-FR6989 — Water meter, extended scan interface (ESI) enabled, ultra-low power MSP430FR6989 evaluation modul

• Bus-powered input voltage range (BP), 0 to 100 mA/port, 4.75 V min to 5.25 V max
• Self-power input voltage range (SP), 0 to 500 mA/port, 4.85 V min to 5.15 V max
• Downstream output voltage range in bus-powered mode, 0 to 100 mA/port, 4.4 V min to 5.25 V max
• Downstream output voltage range in (...)

MSP-EXP430F5529LP — MSP430F5529 USB LaunchPad™ development kit

PSpice for TI 可提供帮助评估模拟电路功能的设计和仿真环境。此功能齐全的设计和仿真套件使用 Cadence 的模拟分析引擎。PSpice for TI 可免费使用，包括业内超大的模型库之一，涵盖我们的模拟和电源产品系列以及精选的模拟行为模型。

借助?PSpice for TI 的设计和仿真环境及其内置的模型库，您可对复杂的混合信号设计进行仿真。创建完整的终端设备设计和原型解决方案，然后再进行布局和制造，可缩短产品上市时间并降低开发成本。

在?PSpice for TI 设计和仿真工具中，您可以搜索 TI (...)

TINA-TI — 基于 SPICE 的模拟仿真程序

TINA-TI 提供了 SPICE 所有的传统直流、瞬态和频域分析以及更多。TINA 具有广泛的后处理功能，允许您按照希望的方式设置结果的格式。虚拟仪器允许您选择输入波形、探针电路节点电压和波形。TINA 的原理图捕获非常直观 - 真正的“快速入门”。

TINA-TI 安装需要大约 500MB。直接安装，如果想卸载也很容易。我们相信您肯定会爱不释手。

TINA 是德州仪器 (TI) 专有的 DesignSoft 产品。该免费版本具有完整的功能，但不支持完整版 TINA 所提供的某些其他功能。

如需获取可用 TINA-TI 模型的完整列表，请参阅：SpiceRack - 完整列表

需要 HSpice (...)