The TUSB2077A hub is a 3.3-V CMOS device that provides up to seven downstream ports in compliance with the USB 2.0 specification. Because this device is implemented with a digital state machine instead of a microcontroller, no software programming is required. Fully compliant USB transceivers are integrated into the ASIC for all upstream and downstream ports. The downstream ports support full-speed and low-speed devices by automatically setting the slew rate according to the speed of the device attached to the ports. The configuration of the BUSPWR terminal selects either the bus-powered or self-powered mode. The introduction of the DP0 pull-up resistor disable terminal, DP0PUR, makes it much easier to implement an onboard bus/self-power dynamic-switching circuitry. The three-LED indicator control output pins also enable the implementation of visualized status monitoring of the hub and its downstream ports. With these new function pins, the end equipment vendor can considerably reduce the total board cost while adding additional product value.

The EXTMEM pin (pin 47) enables or disables the optional EEPROM interface. When EXTMEM is high, the vendor and product IDs (VID and PID) use defaults, such that the message displayed during enumeration is General Purpose USB Hub.

The TUSB2077A supports bus-powered and self-powered modes. External power-management devices, such as the TPS2044, are required to control the 5-V power source switching (on/off) to the downstream ports and to detect an overcurrent condition from the downstream ports individually or ganged. An individually port power controlled hub switches power on or off to each downstream port as requested by the USB host. Also when an individually port power controlled hub senses an overcurrent event, only power to the affected downstream port will be switched off. A ganged hub switches on power to all its downstream ports when power must be on for any port. The power to the downstream ports is not switched off unless all ports are in a state that allows power to be removed. Also, when a ganged hub senses an overcurrent event, power to all downstream ports will be switched off.

• Fully Compliant With the USB Specification as a Full-Speed Hub: TID #20240226
• Integrated USB Transceivers
• 3.3-V Low-Power ASIC Logic
• Two Power Source Modes
  • Self-Powered Mode Supporting Seven Downstream Ports
  • Bus-Powered Mode Supporting Four Downstream Ports
• All Downstream Ports Support Full-Speed and Low-Speed Operations
• Power Switching and Overcurrent Reporting Is Provided Ganged or Per Port
• Supports Suspend and Resume Operations
• Suspend Status Pin Available for External Logic Power Down
• Supports Custom Vendor ID and Product ID With External Serial EEPROM
• 3-State EEPROM Interface Allows EEPROM Sharing
• Push-Pull Outputs for PWRON Eliminate the Need for External Pullup Resistors
• Noise Filtering on OVRCUR Provides Immunity to Voltage Spikes
• Supports 6-MHz Operation Through a Crystal Input or a 48-MHz Input Clock
• New Functional Pins Introduced to Reduce the Board Material Cost
  • 3 LED Indicator Control Outputs Enable Visualized Monitoring of 6 Different Hub/Port Status (HUBCFG, PORTPWR, PORTDIS)
  • Output Pin Available to Disable External Pullup Resistor on DP0 for 15 ms After Reset or After Change on BUSPWR and Enable Easy Implementation of Onboard Bus/Self-Power Dynamic Switching Circuitry
• No Special Driver Requirements; Works Seamlessly With Any Operating System With USB Stack Support
• Available in 48-Pin LQFP Package
• JEDEC Descriptor S–PQFP–G for Low-Profile Quad Flatpack (LQFP).

• Function
• USB2
• USB speed (Mbps)
• 12
• Supply voltage (V)
• 3.3
• Rating
• Catalog
• Operating temperature range (C)
• 0 to 70

TUSB2077A的完整型号有：TUSB2077APT、TUSB2077APTR，以下是这些产品的关键参数及官网采购报价：

TUSB2077APT，工作温度：0 to 70，封装：LQFP (PT)-48，包装数量MPQ：250个，MSL 等级/回流焊峰值温度：Level-3-260C-168 HR，引脚镀层/焊球材料：NIPDAU，TI官网TUSB2077APT的批量USD价格：2.523（1000+）

TUSB2077APTR，工作温度：0 to 70，封装：LQFP (PT)-48，包装数量MPQ：1000个，MSL 等级/回流焊峰值温度：Level-3-260C-168 HR，引脚镀层/焊球材料：NIPDAU，TI官网TUSB2077APTR的批量USD价格：2.06（1000+）

PSPICE-FOR-TI — 适用于 TI 设计和模拟工具的 PSpice

PSpice for TI 可提供帮助评估模拟电路功能的设计和仿真环境。此功能齐全的设计和仿真套件使用 Cadence 的模拟分析引擎。PSpice for TI 可免费使用，包括业内超大的模型库之一，涵盖我们的模拟和电源产品系列以及精选的模拟行为模型。

借助?PSpice for TI 的设计和仿真环境及其内置的模型库，您可对复杂的混合信号设计进行仿真。创建完整的终端设备设计和原型解决方案，然后再进行布局和制造，可缩短产品上市时间并降低开发成本。

在?PSpice for TI 设计和仿真工具中，您可以搜索 TI (...)

TINA-TI — 基于 SPICE 的模拟仿真程序

TINA-TI 提供了 SPICE 所有的传统直流、瞬态和频域分析以及更多。TINA 具有广泛的后处理功能，允许您按照希望的方式设置结果的格式。虚拟仪器允许您选择输入波形、探针电路节点电压和波形。TINA 的原理图捕获非常直观 - 真正的“快速入门”。

TINA-TI 安装需要大约 500MB。直接安装，如果想卸载也很容易。我们相信您肯定会爱不释手。

TINA 是德州仪器 (TI) 专有的 DesignSoft 产品。该免费版本具有完整的功能，但不支持完整版 TINA 所提供的某些其他功能。

如需获取可用 TINA-TI 模型的完整列表，请参阅：SpiceRack - 完整列表

需要 HSpice (...)