The TVP5147M1 device is a high-quality, single-chip digital video decoder that digitizes and decodes all popular baseband analog video formats into digital component video. The TVP5147M1 decoder supports the analog-to-digital (A/D) conversion of component YPbPr signals, as well as the A/D conversion and decoding of NTSC, PAL, and SECAM composite and S-video into component YCbCr. This decoder includes two 11-bit 30-MSPS A/D converters (ADCs). Preceding each ADC in the device, the corresponding analog channel contains an analog circuit that clamps the input to a reference voltage and applies a programmable gain and offset. A total of ten video input terminals can be configured to a combination of YPbPr, CVBS, or S-video video inputs.

Composite or S-video signals are sampled at 2× the ITU-R BT.601 clock frequency, line-locked alignment, and are then decimated to the 1× pixel rate. CVBS decoding uses five-line adaptive comb filtering for both the luma and chroma data paths to reduce both cross-luma and cross-chroma artifacts. A chroma trap filter is also available. On CVBS and S-video inputs, the user can control video characteristics such as contrast, brightness, saturation, and hue via an I²C host port interface. Furthermore, luma peaking (sharpness) with programmable gain is included, as well as a patented chroma transient improvement (CTI) circuit.

The following output formats can be selected: 20-bit 4:2:2 YCbCr or 10-bit 4:2:2 YCbCr.

The TVP5147M1 decoder generates synchronization, blanking, field, active video window, horizontal and vertical syncs, clock, genlock (for downstream video encoder synchronization), host CPU interrupt and programmable logic I/O signals, in addition to digital video outputs.

The TVP5147M1 decoder includes methods for advanced vertical blanking interval (VBI) data retrieval. The VBI data processor (VDP) slices, parses, and performs error checking on teletext, closed caption (CC), and other VBI data. A built-in FIFO stores up to 11 lines of teletext data, and with proper host port synchronization, full-screen teletext retrieval is possible. The TVP5147M1 decoder can pass through the output formatter 2× sampled raw luma data for host-based VBI processing.

The main blocks of the TVP5147M1 decoder include:

• Robust sync detection for weak and noisy signals as well as VCR trick modes
• Y/C separation by 2-D 5-line adaptive comb or chroma trap filter
• Two 11-bit, 30-MSPS A/D converters with analog preprocessors [clamp and automatic gain control (AGC)]
• Analog video output
• Luminance processor
• Chrominance processor
• Clock/timing processor and power-down control
• Software-controlled power-saving standby mode
• Output formatter
• I²C host port interface
• VBI data processor
• Macrovision™ copy protection detection circuit (Type 1, 2, 3, and separate color stripe detection)
• 3.3-V tolerant digital I/O ports

• Two 30-MSPS 11-bit A/D channels with programmable gain control
• Supports NTSC (J, M, 4.43), PAL (B, D, G, H, I, M, N, Nc, 60), and SECAM (B, D, G, K, K1, L) CVBS, and S-video
• Supports analog component YPbPr video format with embedded sync
• Ten analog video input terminals for multisource connection
• Supports analog video output
• User-programmable video output formats
  • 10-bit ITU-R BT.656 4:2:2 YCbCr with embedded syncs
  • 10-bit 4:2:2 YCbCr with separate syncs
  • 20-bit 4:2:2 YCbCr with separate syncs
  • 2x sampled raw VBI data in active video during a vertical blanking period
  • Sliced VBI data during a vertical blanking period or active video period (full field mode)
• HSYNC/VSYNC outputs with programmable position, polarity, width, and field ID (FID) output
• Composite and S-video processing
  • Adaptive 2-D 5-line adaptive comb filter for composite video inputs; chroma-trap available
  • Automatic video standard detection (NTSC/PAL/SECAM) and switching
  • Luma-peaking with programmable gain
  • Patented chroma transient improvement (CTI)
  • Patented architecture for locking to weak, noisy, or unstable signals
  • Single 14.31818-MHz reference crystal for all standards
  • Line-locked internal pixel sampling clock generation with horizontal and vertical lock signal outputs
  • Genlock output RTC format for downstream video encoder synchronization
• Certified Macrovision? copy protection detection
• Available in commercial (0°C to 70°C) and industrial (?40°C to 85°C) temperature ranges
• Qualified for Automotive Applications (AEC-Q100 Rev G ? TVP5147M1IPFPQ1 or TVP5147M1IPFPRQ1)
• VBI data processor
  • Teletext (NABTS, WST)
  • CC and extended data service (EDS)
  • Wide screen signaling (WSS)
  • Copy generation management system (CGMS)
  • Video program system (VPS/PDC)
  • Vertical interval time code (VITC)
  • Gemstar 1×/2× mode
  • V-Chip decoding
  • Register readback of CC, WSS (CGMS), VPS/PDC, VITC and Gemstar 1×/2× sliced data
• I2C host port interface
• Reduced power consumption: 1.8-V digital core, 3.3-V for digital I/O, and 1.8-V/3.3 V analog core with power-save and power-down modes
• 80-terminal TQFP PowerPAD? package

PowerPAD, DLP are trademarks of Texas Instruments. Gemstar is a trademark of Gemstar-TV Guide Intermational. Macrovision is a trademark of Macrovision Corporation. All other trademarks are the property of their respective owners.

• Supply voltage (V)
• 1.8, 3.3
• Operating temperature range (C)
• -40 to 85, 0 to 70

TVP5147M1的完整型号有：TVP5147M1IPFP、TVP5147M1IPFPR、TVP5147M1PFP、TVP5147M1PFPR，以下是这些产品的关键参数及官网采购报价：

TVP5147M1IPFP，工作温度：-40 to 85，封装：HTQFP (PFP)-80，包装数量MPQ：96个，MSL 等级/回流焊峰值温度：Level-3-260C-168 HR，引脚镀层/焊球材料：NIPDAU，TI官网TVP5147M1IPFP的批量USD价格：4.889（1000+）

TVP5147M1IPFPR，工作温度：-40 to 85，封装：HTQFP (PFP)-80，包装数量MPQ：1000个，MSL 等级/回流焊峰值温度：Level-3-260C-168 HR，引脚镀层/焊球材料：NIPDAU，TI官网TVP5147M1IPFPR的批量USD价格：4.19（1000+）

TVP5147M1PFP，工作温度：0 to 70，封装：HTQFP (PFP)-80，包装数量MPQ：96个，MSL 等级/回流焊峰值温度：Level-3-260C-168 HR，引脚镀层/焊球材料：NIPDAU，TI官网TVP5147M1PFP的批量USD价格：4.19（1000+）

TVP5147M1PFPR，工作温度：0 to 70，封装：HTQFP (PFP)-80，包装数量MPQ：1000个，MSL 等级/回流焊峰值温度：Level-3-260C-168 HR，引脚镀层/焊球材料：NIPDAU，TI官网TVP5147M1PFPR的批量USD价格：3.492（1000+）

PSPICE-FOR-TI — 适用于 TI 设计和模拟工具的 PSpice

PSpice for TI 可提供帮助评估模拟电路功能的设计和仿真环境。此功能齐全的设计和仿真套件使用 Cadence 的模拟分析引擎。PSpice for TI 可免费使用，包括业内超大的模型库之一，涵盖我们的模拟和电源产品系列以及精选的模拟行为模型。

借助?PSpice for TI 的设计和仿真环境及其内置的模型库，您可对复杂的混合信号设计进行仿真。创建完整的终端设备设计和原型解决方案，然后再进行布局和制造，可缩短产品上市时间并降低开发成本。

在?PSpice for TI 设计和仿真工具中，您可以搜索 TI (...)

TINA-TI — 基于 SPICE 的模拟仿真程序

TINA-TI 提供了 SPICE 所有的传统直流、瞬态和频域分析以及更多。TINA 具有广泛的后处理功能，允许您按照希望的方式设置结果的格式。虚拟仪器允许您选择输入波形、探针电路节点电压和波形。TINA 的原理图捕获非常直观 - 真正的“快速入门”。

TINA-TI 安装需要大约 500MB。直接安装，如果想卸载也很容易。我们相信您肯定会爱不释手。

TINA 是德州仪器 (TI) 专有的 DesignSoft 产品。该免费版本具有完整的功能，但不支持完整版 TINA 所提供的某些其他功能。

如需获取可用 TINA-TI 模型的完整列表，请参阅：SpiceRack - 完整列表

需要 HSpice (...)