The UCD30xx devices are members of a family of digital PWM controllers from Texas Instruments providing a single-chip control solution for digital power-conversion applications. These devices allow digital control implementation of a high-performance, high-frequency power supply with flexible configuration of parameters, supervisory, monitoring, and communication functions.

The UCD30xx are fully programmable solutions that are configurable to support a wide range of isolated and non-isolated topologies in single- or multiphase configurations. Some examples include interleaved PFC, isolated forward, half-bridge, phase-shifted full bridge, active clamp, and resonant LLC.

At the core of the UCD30xx controllers are the digital control-loop peripherals, also known as Fusion Digital Power peripherals (FDPP). Each FDPP implements a high-speed digital control loop consisting of a dedicated error analog-to-digital converter (EADC), a three-pole/three-zero (3p, 3z) digital compensator, and two DPWM outputs with 250-ps pulse-width resolution. The device also contains a 12-bit, 200-ksps general-purpose ADC with up to 15 channels, timers, interrupt controls, and communications ports such as PMBus, SCI, and SPI. The device is based on a 32-bit ARM7 RISC CPU that performs real-time monitoring, configures peripherals, and manages communications. The CPU executes its program out of programmable flash memory as well as ROM.

The UCD30xx is supported by Texas Instruments' Code Composer Studio software development environment.

Digital Control of up to Four Voltage Feedback Loops

Up to Eight High-Resolution Digital Pulsewidth Modulated (DPWM) Outputs for Supporting a Wide Range of Offline, Isolated and Non-Isolated DC-to-DC Topologies

• 250-ps DPWM Pulse-Width Resolution
• 4-ns DPWM Frequency Resolution
• Adjustable Phase Shift Between DPWM Outputs
• Adjustable Dead Band Between Each DPWM Pair
• Active-High or -Low DPWM Polarity
• Up to 2-MHz DPWM Switching Frequency

Dedicated High-Speed Error Analog-to-Digital Converter (EADC) for Each Feedback Loop With Sense Resolution of up to 1 mV

On-Chip 10-Bit D and A Converter (DAC) for Setting EADC Reference Voltage

Dedicated Hardware Accelerated Digital Compensators or Control Law Accelerators (CLA)

• Three-Pole, Three-Zero Configurable Compensator
• Features Non-Linear Digital Control
• Multiple Programmable Coefficient Registers for Adaptive Digital Compensation

Up to 15-Channel, 12-Bit, 200-ksps, Analog-to-Digital Converter (ADC)

Multiple Levels of Fault Protection

• Four High-Speed Analog Comparators
• External Fault Inputs
• 12-Bit ADC

Configurable for Voltage-Mode, Average-Current-Mode, and Resonant-Mode Control

Allows Synchronization of DPWM Waveforms Between Multiple UCD3040, UCD3020 and UCD3028 (UCD30xx) Devices

Adjustable DPWM Pulse Width Enables Support for Current Balancing in a Multiphase Application.

High-Performance 31.25-MHz, 32-Bit ARM7 Processor

32-KByte Program Flash and 2-KByte Data Flash Memory With Error Correction Code (ECC)

4-KByte Data RAM

4-KByte Boot ROM

Communication Peripherals

• PMBus
• UART
• SPI
• JTAG (Not Available in the UCD3028)

Single-Supply Solution: Internal Regulator Controls External Pass Element

Internal Temperature Sensor

Up to Five Additional Timers

Built-In Watchdog, BOD, and POR

80-Pin QFP (PFC), 64-Pin QFN (RGC), 48-Pin QFN (RGZ), and 40-Pin QFN (RHA and RMH) Package Offerings

Operating Temperature Range: –40°C to 125°C

APPLICATIONS

• Isolated AC-to-DC and DC-to-DC Power Supplies
• Power-Factor Correction
• Non-Isolated DC-to-DC Power Supplies

• Number of outputs
• 8
• Frequency (Max) (kHz)
• 2000
• Number of ADC channels
• 15
• Analog comparators
• 4
• Communications
• 1 PMBUS, 1 SPI, 1 UART
• Compensator
• 3-pole/3-zero
• DPWM resolution (ps)
• 250
• GPIOs
• 26, 33
• Number of digital power peripheral feedback loops
• 4
• Non-volatile memory
• 2kB (Data), 32kB (Program)
• Processor
• 31.25MHz, 32-bit ARM7
• Operating temperature range (C)
• -40 to 125
• Rating
• Catalog

UCD3040的完整型号有：UCD3040PFC、UCD3040PFCR、UCD3040RGCR、UCD3040RGCT，以下是这些产品的关键参数及官网采购报价：

UCD3040PFC，工作温度：-40 to 125，封装：TQFP (PFC)-80，包装数量MPQ：96个，MSL 等级/回流焊峰值温度：Level-2-260C-1 YEAR，引脚镀层/焊球材料：NIPDAU，TI官网UCD3040PFC的批量USD价格：3.96（1000+）

UCD3040PFCR，工作温度：-40 to 125，封装：TQFP (PFC)-80，包装数量MPQ：1000个，MSL 等级/回流焊峰值温度：Level-2-260C-1 YEAR，引脚镀层/焊球材料：NIPDAU，TI官网UCD3040PFCR的批量USD价格：3.3（1000+）

UCD3040RGCR，工作温度：-40 to 125，封装：VQFN (RGC)-64，包装数量MPQ：2000个，MSL 等级/回流焊峰值温度：Level-3-260C-168 HR，引脚镀层/焊球材料：NIPDAU，TI官网UCD3040RGCR的批量USD价格：4.7（1000+）

UCD3040RGCT，工作温度：-40 to 125，封装：VQFN (RGC)-64，包装数量MPQ：250个，MSL 等级/回流焊峰值温度：Level-3-260C-168 HR，引脚镀层/焊球材料：NIPDAU，TI官网UCD3040RGCT的批量USD价格：5.36（1000+）

TMDSEMU200-U — Spectrum Digital XDS200 USB 仿真器

Spectrum Digital XDS200 是最新 XDS200 系列 TI 处理器调试探针（仿真器）的首个模型。XDS200 系列拥有超低成本 XDS100 与高性能 XDS560v2 之间的低成本与高性能的完美平衡。此外，对于带有嵌入式缓冲跟踪器 (ETB) 的所有 ARM 和 DSP 处理器，所有 XDS 调试探针均支持内核和系统跟踪。

Spectrum Digital XDS200 通过 TI 20 引脚连接器（带有适合 TI 14 引脚、TI 10 引脚和 ARM 20 引脚的多个适配器）连接到目标板，而通过 USB2.0 高速连接 (480Mbps) 连接到主机 PC。要在主机 (...)

CCSTUDIO — Code Composer Studio 集成式开发环境 (IDE)

Fusion Digital Power图形用户界面 (GUI) 软件用于配置和监视精选的德州仪器 (TI) 数字电源控制器以及序列发生器/运行状况监视器。此应用程序使用 PMBus 协议通过 TI USB 适配器经由串行总线与器件进行通信。

FUSION_MFR_GUI — Fusion Digital Power 制造工具

The Fusion Digital Power Manufacturing Tool (aka MFR GUI) is a Graphical User Interface used to download firmware, upgrade firmware, configure, calibrate and test .

The MFR GUI supports the same devices as Fusion Digital Power Designer software. This tool is typically used in manufacturing (...)

UCD3PROG-FR03TXI0 — FlashRunner™ FR03 系统内编程器

FlashRunnerTM FR03 is a high-performance, standalone In-System Programmer for Flash-based microcontrollers and serial memories. FlashRunnerTM FR03, which is targeted at production environments, easily interfaces to a programming system or Automatic Test Equipment (ATE) and can work either in full (...) 发件人： SMH Technologies

Fusion Digital Power Studio 3.0.77 (Rev. M)

PSpice for TI 可提供帮助评估模拟电路功能的设计和仿真环境。此功能齐全的设计和仿真套件使用 Cadence 的模拟分析引擎。PSpice for TI 可免费使用，包括业内超大的模型库之一，涵盖我们的模拟和电源产品系列以及精选的模拟行为模型。

借助?PSpice for TI 的设计和仿真环境及其内置的模型库，您可对复杂的混合信号设计进行仿真。创建完整的终端设备设计和原型解决方案，然后再进行布局和制造，可缩短产品上市时间并降低开发成本。

在?PSpice for TI 设计和仿真工具中，您可以搜索 TI (...)