The UCD9224 is a multi-rail, multi-phase synchronous buck digital PWM controller designed for non-isolated DC/DC power applications. This device integrates dedicated circuitry for DC/DC loop management with flash memory and a serial interface to support configurability, monitoring and management.

The UCD9224 was designed to provide a wide variety of desirable features for non-isolated DC/DC converter applications while minimizing the total system component count by reducing external circuits. The solution integrates multi-loop management with sequencing, margining, tracking and intelligent phase management to optimize for total system efficiency. Additionally, loop compensation and calibration are supported without the need to add external components.

To facilitate configuring the device, the Texas Instruments Fusion Digital Power™ Designer is provided. This PC based Graphical User Interface offers an intuitive interface to the device. This tool allows the design engineer to configure the system operating parameters for the application, store the configuration to on-chip non-volatile memory and observe both frequency domain and time domain simulations for each of the power stage outputs.

TI has also developed multiple complementary power stage solutions – from discrete drivers in the UCD7k family to fully tested power train modules in the PTD family. These solutions have been developed to complement the UCD9k family of system power controllers.

• Fully Configurable Multi-Output and Multi- Phase Non-Isolated DC/DC PWM Controller
• Controls Up to 2 Voltage Rails and Up to 4 Phases
• Supports Switching Frequencies Up to 2MHz with 250 ps Duty-Cycle Resolution
• Up To 1mV Closed Loop Resolution
• Hardware-Accelerated, 3-Pole/3-Zero Compensator with Non-Linear Gain for Improved Transient Performance
• Supports Multiple Soft-Start and Soft-Stop Configurations Including Prebias Start-up
• Supports Voltage Tracking, Margining and Sequencing
• Supports Current and Temperature Balancing for Multi-Phase Power Stages
• Supports Phase Adding/Shedding for Multi-Phase Power Stages
• Sync In/Out Pins Align DPWM Clocks Between Multiple UCD92xx Devices
• 12-Bit Digital Monitoring of Power Supply Parameters Including:
  • Input/Output Current and Voltage
  • Temperature at Each Power Stage
• Multiple Levels of Over-current Fault Protection:
  • External Current Fault Inputs
  • Analog Comparators Monitor Current Sense Voltage
  • Current Continually Digitally Monitored
• Over- and Under-voltage Fault Protection
• Over-temperature Fault Protection
• Enhanced Nonvolatile Memory with Error Correction Code (ECC)
• Device Operates From a Single Supply with an Internal Regulator Controller That Allows Operation Over a Wide Supply Voltage Range
• Supported by Fusion Digital Power Designer, a Full Featured PC Based Design Tool to Simulate, Configure, and Monitor Power Supply Performance
• APPLICATIONS
  • Industrial/ATE
  • Networking Equipment
  • Telecommunications Equipment
  • Servers
  • Storage Systems
  • FPGA, DSP and Memory Power

• Number of outputs
• 2
• Frequency (Max) (kHz)
• 2000
• Number of ADC channels
• 2
• Analog comparators
• 3
• Communications
• 1 I2C, 1 PMBUS
• Compensator
• 3-pole/3-zero
• DPWM resolution (ps)
• 250
• GPIOs
• 0
• Number of digital power peripheral feedback loops
• 2
• Non-volatile memory
• 32kB (Program)
• Processor
• —
• Operating temperature range (C)
• -40 to 125
• Rating
• Catalog

UCD9224的完整型号有：UCD9224RGZR、UCD9224RGZT，以下是这些产品的关键参数及官网采购报价：

UCD9224RGZR，工作温度：-40 to 125，封装：VQFN (RGZ)-48，包装数量MPQ：2500个，MSL 等级/回流焊峰值温度：Level-3-260C-168 HR，引脚镀层/焊球材料：NIPDAU，TI官网UCD9224RGZR的批量USD价格：2.682（1000+）

UCD9224RGZT，工作温度：-40 to 125，封装：VQFN (RGZ)-48，包装数量MPQ：250个，MSL 等级/回流焊峰值温度：Level-3-260C-168 HR，引脚镀层/焊球材料：NIPDAU，TI官网UCD9224RGZT的批量USD价格：3.148（1000+）

UCD9224EVM-464 — 用于 UCD9224 数字 PWM 系统控制器的评估模块

UCD9224EVM-464 可通过 UCD9224 数字控制器和 PTD08D210W 电源传动模块设计成两个独立的单相 POL 电压轨。电压轨经过预先配备，可在 12V +/- 10% 的输入电压源下工作，并产生 2.5V (Vout1) 和 1.2V (Vout2) 的输出电压，且两种电压都支持高达 10A 的输入电流。作为 PTD08D210W 的元件，UCD7242 双路同步降压功率驱动器结合并优化了 MOSFET 驱动器、用于两个电压轨的高低侧功率 MOSFET，以及集成了数字控制器的故障和监控电路。

如果设计师想使用计算机监控或修改 UCD9224EVM-464，建议使用单独的 (...)

TMDSEMU200-U — Spectrum Digital XDS200 USB 仿真器

Spectrum Digital XDS200 是最新 XDS200 系列 TI 处理器调试探针（仿真器）的首个模型。XDS200 系列拥有超低成本 XDS100 与高性能 XDS560v2 之间的低成本与高性能的完美平衡。此外，对于带有嵌入式缓冲跟踪器 (ETB) 的所有 ARM 和 DSP 处理器，所有 XDS 调试探针均支持内核和系统跟踪。

Spectrum Digital XDS200 通过 TI 20 引脚连接器（带有适合 TI 14 引脚、TI 10 引脚和 ARM 20 引脚的多个适配器）连接到目标板，而通过 USB2.0 高速连接 (480Mbps) 连接到主机 PC。要在主机 (...)

FUSION_DIGITAL_POWER_DESIGNER — Digital Power 软件

Fusion Digital Power图形用户界面 (GUI) 软件用于配置和监视精选的德州仪器 (TI) 数字电源控制器以及序列发生器/运行状况监视器。此应用程序使用 PMBus 协议通过 TI USB 适配器经由串行总线与器件进行通信。

FUSION_MFR_GUI — Fusion Digital Power 制造工具

The Fusion Digital Power Manufacturing Tool (aka MFR GUI) is a Graphical User Interface used to download firmware, upgrade firmware, configure, calibrate and test .

The MFR GUI supports the same devices as Fusion Digital Power Designer software. This tool is typically used in manufacturing (...)

PSPICE-FOR-TI — 适用于 TI 设计和模拟工具的 PSpice

PSpice for TI 可提供帮助评估模拟电路功能的设计和仿真环境。此功能齐全的设计和仿真套件使用 Cadence 的模拟分析引擎。PSpice for TI 可免费使用，包括业内超大的模型库之一，涵盖我们的模拟和电源产品系列以及精选的模拟行为模型。

借助?PSpice for TI 的设计和仿真环境及其内置的模型库，您可对复杂的混合信号设计进行仿真。创建完整的终端设备设计和原型解决方案，然后再进行布局和制造，可缩短产品上市时间并降低开发成本。

在?PSpice for TI 设计和仿真工具中，您可以搜索 TI (...)