The UCD9244 is a four-rail synchronous buck digital PWM controller designed for non-isolated DC/DC power applications. This device integrates dedicated circuitry for DC/DC loop management with support for up to four VID interfaces. Additionally, the UCD9244 has flash memory and a serial interface to support configurability, monitoring and management.

Several Voltage Identification (VID) modes are supported, including a 4-bit parallel interface, a 6-bit interface and an 8-bit serial interface.

The UCD9244 was designed to provide a wide variety of desirable features for non-isolated DC/DC converter applications while minimizing the total system component count by reducing external circuits. The solution integrates multi-loop management with sequencing, margining and tracking to optimize for total system efficiency. Additionally, loop compensation and calibration are supported without the need to add external components.

To facilitate configuring the device, the Texas Instruments Fusion Digital Power™ Designer is provided. This PC based Graphical User Interface offers an intuitive interface to the device. This tool allows the design engineer to configure the system operating parameters for the application, store the configuration to on-chip non-volatile memory and observe both frequency domain and time domain simulations for each of the power stage outputs.

TI has also developed multiple complementary power stage solutions – from discrete drivers in the UCD7k family to fully tested power train modules in the PTD family. These solutions have been developed to complement the UCD92xx family of system power controllers.

• Fully Configurable Four-Output Non-Isolated DC/DC PWM Controller with support for TMS320C6670? and TMS320C6678? DSP VID interface
• Supports Switching Frequencies Up to 2MHz With 250 ps Duty-Cycle Resolution
• Up To 1mV Closed Loop Resolution
• Hardware-Accelerated, 3-Pole/3-Zero Compensator with Non-Linear Gain for Improved Transient Performance
• Supports Multiple Soft-Start and Soft-Stop Configurations Including Prebias Start-up
• Supports Voltage Margining and Sequencing
• Sync In Pin Aligns DPWM Clocks Between Multiple UCD92xx Devices
• 12-Bit Digital Monitoring of Power Supply Parameters Including:
  • Input Current and Voltage
  • Output Current and Voltage
  • Temperature at Each Power Stage
  • Auxiliary ADC Inputs
• Multiple Levels of Over-current Fault Protection:
  • External Current Fault Inputs
  • Analog Comparators Monitor Current Sense Voltage
  • Current Continually Digitally Monitored
• Over and Under-voltage Fault Protection
• Over-temperature Fault Protection
• Enhanced Nonvolatile Memory With Error Correction Code (ECC)
• Device Operates From a Single Supply With an Internal Regulator Controller That Allows Operation Over a Wide Supply Voltage Range
• Supported by Fusion Digital Power? Designer, a Full Featured PC Based Design Tool to Simulate, Configure, and Monitor Power Supply Performance.
• APPLICATIONS
  • Networking Equipment
  • Telecommunications Equipment
  • FPGA, DSP, and Memory Power

TMS320C6670, TMS320C6678, Fusion Digital Power, Auto-ID are trademarks of Texas Instruments.

• Number of outputs
• 4
• Frequency (Max) (kHz)
• 2000
• Number of ADC channels
• 4
• Analog comparators
• 4
• Communications
• 1 I2C, 1 PMBUS
• Compensator
• 3-pole/3-zero
• DPWM resolution (ps)
• 250
• GPIOs
• 1
• Number of digital power peripheral feedback loops
• 4
• Non-volatile memory
• 32kB (Program)
• Processor
• —
• Operating temperature range (C)
• -40 to 125, -40 to 85
• Rating
• Catalog

UCD9244的完整型号有：UCD9244ARGCR、UCD9244ARGCT、UCD9244RGCR、UCD9244RGCT，以下是这些产品的关键参数及官网采购报价：

UCD9244ARGCR，工作温度：-40 to 85，封装：VQFN (RGC)-64，包装数量MPQ：3000个，MSL 等级/回流焊峰值温度：Level-3-260C-168 HR，引脚镀层/焊球材料：NIPDAU，TI官网UCD9244ARGCR的批量USD价格：4.21（1000+）

UCD9244ARGCT，工作温度：-40 to 85，封装：VQFN (RGC)-64，包装数量MPQ：250个，MSL 等级/回流焊峰值温度：Level-3-260C-168 HR，引脚镀层/焊球材料：NIPDAU，TI官网UCD9244ARGCT的批量USD价格：4.942（1000+）

UCD9244RGCR，工作温度：-40 to 125，封装：VQFN (RGC)-64，包装数量MPQ：2000个，MSL 等级/回流焊峰值温度：Level-3-260C-168 HR，引脚镀层/焊球材料：NIPDAU，TI官网UCD9244RGCR的批量USD价格：4.21（1000+）

UCD9244RGCT，工作温度：-40 to 125，封装：VQFN (RGC)-64，包装数量MPQ：250个，MSL 等级/回流焊峰值温度：Level-3-260C-168 HR，引脚镀层/焊球材料：NIPDAU，TI官网UCD9244RGCT的批量USD价格：4.942（1000+）

TMDSEMU200-U — Spectrum Digital XDS200 USB 仿真器

Spectrum Digital XDS200 是最新 XDS200 系列 TI 处理器调试探针（仿真器）的首个模型。XDS200 系列拥有超低成本 XDS100 与高性能 XDS560v2 之间的低成本与高性能的完美平衡。此外，对于带有嵌入式缓冲跟踪器 (ETB) 的所有 ARM 和 DSP 处理器，所有 XDS 调试探针均支持内核和系统跟踪。

Spectrum Digital XDS200 通过 TI 20 引脚连接器（带有适合 TI 14 引脚、TI 10 引脚和 ARM 20 引脚的多个适配器）连接到目标板，而通过 USB2.0 高速连接 (480Mbps) 连接到主机 PC。要在主机 (...)

PSPICE-FOR-TI — 适用于 TI 设计和模拟工具的 PSpice

PSpice for TI 可提供帮助评估模拟电路功能的设计和仿真环境。此功能齐全的设计和仿真套件使用 Cadence 的模拟分析引擎。PSpice for TI 可免费使用，包括业内超大的模型库之一，涵盖我们的模拟和电源产品系列以及精选的模拟行为模型。

借助?PSpice for TI 的设计和仿真环境及其内置的模型库，您可对复杂的混合信号设计进行仿真。创建完整的终端设备设计和原型解决方案，然后再进行布局和制造，可缩短产品上市时间并降低开发成本。

在?PSpice for TI 设计和仿真工具中，您可以搜索 TI (...)